9 Lessons Your Parents Taught You About Fiat Panda Key Fob Replacement
Reasons Your Fiat 500 Key Fob Won't Work
A Fiat 500 key fob makes it easy to open doors and start your vehicle. However, there are numerous reasons the fob could stop working. This includes a dead coin-battery, water damage, problems with receiver modules, as well as interference.
This listing is for a NEW replacement Fiat Flip Key Remote - an exact replica of the Ilco brand that must be programmed professionally by a local locksmith (click here to search for a Locksmith Search). This remote includes trunk, lock and unlock buttons.
Dead Coin Battery
The most common reason your 500 key fob won't work is an inactive battery. Modern key fobs have limited operating range and must be within a few inches of the vehicle in order to function. If you're far from your vehicle and press the key fob button, the car will not respond, and will display a "Key Fob Not Detected" message in the instrument cluster.
If this occurs If this happens, replace the battery in the coin-cell (Part Number CR2032) by a new one of a trusted brand such as Panasonic Duracell or Energizer. You can find them at the local hardware store or on the internet.
After you've replaced the coin cell battery You can test it by standing close to your Fiat 500 and pressing the buttons. The car will blink its parking lights and the key fob will operate the lock and unlock buttons.
If your fob's key does not work after replacing the battery, there could be water damage that has prevented it from interacting with the module inside your vehicle. Water damage can happen in a number of ways, ranging from an accidental splash to submerging the fob salt water at the beach. If you suspect your fob has been exposed to water, put it in a dry rice bag to draw the moisture out. If that doesn't work your fob is likely to need to be reset by a professional auto locksmith or dealer.
Water Damage
The fob does have rubber seals that keep water out of the chip's electronic circuit and out of the ocean or washing it in a machine could cause water damage. Saltwater can cause the circuit board to short and then end up dying. Getting the fob wet is not an option however, if you drop it in a cup of water or don't remember to take it out of your pants pocket before running the washing machine and you don't have a chance, don't give in.
First take the battery off the fob. Before replacing thekeylab.co.uk clean the electronic chip with isopropyl or similar products. Test the fob next to verify if it's working. If the fob doesn't function, it may need to be reset. This is usually done by an auto locksmith or dealer.
If the key is older and was not programmed to your vehicle It is likely that it needs to be replaced completely. This is an easy process that can be carried out by a professional automotive locksmith. The locksmith will require the key to be cut to match your vehicle's ignition. They will also need to program the fob into the car's system. This is a low-cost and quick process that could be completed within the same day.
Receiver Module Issues
Your 500 key fob might not work because it's out of range. The remote typically has 30 feet of range or less and if it's far from your car, it will not respond to your commands. This can easily be resolved by moving it closer to your vehicle until it starts responding.
If you've replaced the battery on your coin (commonly known as"button" or "button" or "watch") and the fob won't work it could be due to an internal circuit board problem. Reprogramming the fob typically resolves this issue. There are instructions on how to do this for most vehicles by searching YouTube or checking out the owner's manual.
It is sometimes necessary to replace the metal clips that hold the coin batteries in place. If they loose tension, it could hinder the coin battery from sitting properly and cause your remote to malfunction.
In rare cases the fob can become out of sync with your vehicle because due to hardware or software issues. This could cause a significant headache, but you can frequently fix this issue by visiting a local dealer or auto locksmith to reprogram your fob for you. In certain instances it may be necessary to reinstall the software in your body control module too.
Interference
In addition to a dead coin battery, the key fob may not be receiving or transmitting an signal due to interference. This is possible when the key fob is in proximity to an electronic radio transmitter (cell phones or radar detectors) or any other source of electromagnetic radiation. Other reasons the key fob might not work could be due to a weak connection to the buttons, damage to the internal chip, or water damage.
If the key fob stopped working one day out of the blue or even after trying everything you can do at home to resolve it e.g. You may have a faulty 500 receiver module If you've tried replacing it with a battery, reprogramming it, or using a spare key fob. The receiver module, located beneath the dashboard, receives radio frequency signals from your key fob. It transforms the signals into electronic commands that are then processed by the vehicle.
Fortunately, there's an easy method to reset all of the onboard systems in your 500, including the key fob. Disconnect the battery of 12 volts for about 15 minutes by disconnecting the negative cable first then the positive cable. Then reconnect the battery. This will clear out any residual electricity and restart the car's computer system, which could allow you to get your key fob working again. If the issue continues you should speak with an expert technician. They will be able to identify the exact cause of any problems.